Ascend Pipeline Betriebsanweisung Seite 28
- Seite / 321
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Configuring WAN Connections
Connection profiles
Pipeline User’s Guide Preliminary January 30, 1998 1-9
Route IP=Yes
Route IPX=No
Bridge=No
Note:
You must have routing or bridging globally enabled in the Ethernet >
Mod Config menu or in the Configure menu in order to route or bridge in a
Connection profile.
3
Set the Recv Auth parameter to PAP, CHAP, or Either. An incoming call
must then match a Connection profile in order to be accepted. If the
parameter is set to Either, any authentication scheme supported by both hosts
can be used, including MS-CHAP. If Recv Auth is set to None, incoming
MP+ or PPP calls are not required to provide a password. (For further
discussion of PAP, CHAP, and MS-CHAP, see the Chapter 7, “Setting Up
Pipeline Security.”)
4
Set the bandwidth parameters as appropriate.
The bandwidth settings in the Answer profile apply to incoming calls for
which no Connection profile exists. If a Connection profile exists, its settings
take precedence. (For a discussion of bandwidth settings, see “Example
MP+ configuration” on page 1-19.)
5
Close and save the Answer profile.
Connection profiles
Connection profiles contain parameters that define individual connections. To set
up a basic Connection profile, do the following:
1
Open Ethernet > Connection > any profile.
For example:
20-101 Corporate-gateway
>Station=Corporate-gateway
Active=Yes
Encaps=MPP
Dial #=nnnnnnnnnn
Calling #=
Called #=
Route IP=Yes
Route IPX=N/A
Bridge=N/A
- Pipeline User’s Guide 1
- Ascend Customer Service 3
- Contents 5
- About This Guide 16
- Documentation conventions 17
- Manual set 19
- Configuring WAN Connections 20
- Link encapsulation 21
- Nailed groups 22
- How calls are initiated 23
- How calls are answered 24
- Data compression options 25
- The Answer profile 26
- Connection profiles 28
- Session options 30
- Telco options 31
- Encapsulation options 32
- MP, MPP, and MP+ connections 34
- Monitoring DBA 37
- Example MP+ configuration 38
- BACP connections 40
- Nailed MPP connections 42
- Inverse ARP for Frame Relay 49
- Configuring IP Routing 51
- Host-to-router connections 52
- Router-to-router connections 53
- Subnet mask notation 54
- RIP-v2 and RIP-v1 routing 59
- Interface-based routing 60
- Managing the routing table 64
- Static and dynamic routes 66
- Configuring static routes 66
- Configuring the default route 69
- If you are using RIP-v1 71
- Route preferences 74
- Viewing the routing table 75
- Fields in the routing table 77
- 10.8.9.10 82
- 10.2.3.1 82
- Host with ISDN 82
- Example router connection 83
- Foreign and home agents 87
- IP Address Management 90
- IP Adrs=10.2.3.1 92
- Gateway=10.0.0.17 93
- Active=Yes 93
- Dest=0.0.0.0/0 93
- Metric=1 93
- Private=Yes 93
- Enabling DNS on the Pipeline 96
- Generating UDP checksums 96
- BOOTP Relay 98
- Configuring DHCP services 100
- DHCP services 101
- Setting up a DHCP server 103
- Setting up DHCP spoofing 103
- Local DNS host address table 106
- Creating the local DNS table 108
- Editing the local DNS table 109
- Translation table size 113
- Multiple-address NAT 114
- NAT for Frame Relay 117
- Well-known ports 121
- Configuring IPX Routing 122
- Extensions to standard IPX 124
- Required settings 126
- IPX Route profiles 127
- IPX SAP filters 128
- Dial Query 129
- Watchdog spoofing 130
- Automatic SPX spoofing 130
- IPX in the Answer profile 132
- IPX SAP proxy servers 135
- Managing IPX SAP filters 142
- Applying an IPX SAP filter 144
- Ethernet 146
- About IPX bridging 156
- Enabling bridging 158
- Managing the bridge table 159
- Static bridge-table entries 160
- 10.2.3.4/24 168
- 10.2.3.75/24 168
- 10.2.3.8/24 168
- 10.2.3.100/24 168
- Introduction to filters 170
- Predefined call filters 174
- Overview of Filter profiles 175
- Defining IP filter conditions 179
- Example filters 181
- NetWare Call filter 190
- IP Call filter 195
- AppleTalk Call filter 195
- When packets are not captured 197
- Displaying packets 198
- Example 2 199
- Example 3 200
- Example 4 201
- Example 5 202
- Secure Access Firewalls 203
- Filter persistence 205
- Setting Up Pipeline Security 207
- Recommended security measures 208
- Assigning a Telnet password 211
- Pipeline Security profiles 213
- Default security level 214
- Security profile passwords 214
- Security privileges 214
- Using the Full Access profile 215
- Connection security 217
- Authentication protocols 218
- Callback security 221
- Expect callback support 222
- Using security cards 223
- Requesting PAP-TOKEN mode 225
- Requesting CACHE-TOKEN 226
- Setting system values 233
- Syslog messages 236
- Using DO commands 239
- Resetting the Pipeline 244
- Terminal server commands 246
- IpAddress: ttt.ttt.ttt.ttt 250
- Pipeline 75 Voice Features 251
- Ordering voice features 253
- Caller ID supported 256
- Using Call Waiting 256
- Using Call Hold 257
- Call conferencing 258
- EAZ Terminal ID for Germany 260
- IDSL Implementations 261
- Making voice calls over IDSL 264
- APP Server utility 265
- C:\NOVELL\LSL.COM 273
- C:\NOVELL\XXXODI.COM 273
- C:\ASCEND\APPSRVDS.EXE 273
- C:\ASCEND\ 274
- Troubleshooting 278
- General problems 279
- 100 terminal 281
- ISDN BRI interface problems 284
- Bridge/router problems 286
- Check the installation 287
- Configuration problems 288
- Upgrading system software 291
- Network Interfaces 292
- The upgrade procedure 293
- Activating a Security Profile 294
- Before you begin 296
- Glossary 304
- Broadcast packets 305
- VT-100 terminal emulation 307
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern